Verschillen

Dit geeft de verschillen weer tussen de geselecteerde revisie en de huidige revisie van de pagina.

--- overig:compaq:softpaq:sp0030 [08-01-2022] – aangemaakt michel
+++ overig:compaq:softpaq:sp0030 [08-01-2022] (huidige) – aangemaakt michel
@@ Regel 3: / Regel 3: @@
 ---- dataentry compaq_softpaq ----
 Extensie  : zip
-Grootte   : 20 kB
+Grootte   : 11 kB
-Titel     : This device driver is used with COMPAQ Enhanced Graphics Adaptors (EGA) and Video Graphics Adaptors (VGA) attached to a NEC Multi-Synch II Monitor to enable them to maintain synch.
+Titel     : This device driver enables an IBM Enhanced Graphics Adaptor (EGA) to be run in any COMPAQ 80486-based system.  Otherwise it comes up in 40 cloumn mode and nver gets full EGA functionality.
 Versie    :
 Taal      :
@@ Regel 15: / Regel 15: @@
 ^ Bestand      ^
-| CONFIG.SYS   |
+| MNMIHEEM.DOC |
-| NECIIFIX.DOC |
+| MNMIHEEM.SYS |
-| NECIIFIX.SYS |
 ===== Tekst-bestanden =====
-<file txt CONFIG.SYS>
+<file txt MNMIHEEM.DOC>
-device=neciifix.sys
+                                MNMIHEEM.SYS
+                         INSTALLATION INSTRUCTIONS
-</file>
-April 15, 1988
-Problem:  NEC Multisync II snaps, pops and loses video during a mode
+INTRODUCTION:
-change.  This is a result of the EGA ROM disabling the video connector.
-Solution:  The following line may be entered in the CONFIG.SYS file:
+    MNMIHEEM.SYS is a program executed from CONFIG.SYS that allows an IBM
-  DRIVER=NECIIFIX.SYS
+    EGA adapter to function properly in any Compaq 486-based system.
-This driver will prevent the problem except during power-up or boot.
-The EGA ROM must be changed to be effective during power-up and boot.
-<file txt NECIIFIX.DOC>
+SYSTEM REQUIREMENTS:
+    Any Compaq system that:
+.  Uses an Intel 486 processor.
+.  Has an IBM EGA adapter installed.
+.  Uses DOS version 3.0 or newer as its operating system.
+WHO SHOULD USE:
+    When an IBM EGA adapter is placed in a Compaq 486-based system, three
+    beeps (one very long, two long) occur during initialization.  The
+    machine then boots in 40-column mode.  In an MS-DOS environment, the
+    adapter can be returned to 80-column mode by typing MODE CO80 from a
+    DOS prompt, however, all EGA functionality is NOT regained.
+HOW TO USE:
+    Copy the file MNMIHEEM.SYS to the disk or diskette you will be booting
+    from, using the DOS copy command:
+         copy a:\mnmiheem.sys d:\path\mnmiheem.sys
+    where d:\path\mnmiheem.sys shows the drive and directory in which the
+    program is to be stored and the device from which to boot.
+    Using the file editor of your choice, place the following line as the
+    first line in the CONFIG.SYS file:
+         device=d:\path\mnmiheem.sys.
+    When the system boots, the beeps described above still occur, but
+    shortly thereafter the screen goes blank for a short period and then
+    displays in 80-column mode.  No installation messages are given.
+EFFECTS ON YOUR SYSTEM:
+    After re-initializing the EGA adapter, this program leaves no residue
+    in your system.
 </file>