Verschillen

Dit geeft de verschillen weer tussen de geselecteerde revisie en de huidige revisie van de pagina.

--- overig:compaq:softpaq:sp0030 [08-01-2022] – aangemaakt michel
+++ overig:compaq:softpaq:sp0030 [08-01-2022] (huidige) – aangemaakt michel
@@ Regel 4: / Regel 4: @@
 Extensie  : zip
 Grootte   : 11 kB
-Titel     : This program will prevent system lockup and screen display problems seen with COMPAQ 80386-based systems running NURSING STAFFING PROGRAM by Medical Information Processing Systems, Inc.
+Titel     : This device driver enables an IBM Enhanced Graphics Adaptor (EGA) to be run in any COMPAQ 80486-based system.  Otherwise it comes up in 40 cloumn mode and nver gets full EGA functionality.
 Versie    :
 Taal      :
@@ Regel 15: / Regel 15: @@
 ^ Bestand      ^
-| NEWMENU.COM  |
+| MNMIHEEM.DOC |
-| NEWMENU.DOC  |
+| MNMIHEEM.SYS |
 ===== Tekst-bestanden =====
-<file txt NEWMENU.DOC>
+<file txt MNMIHEEM.DOC>
+                                MNMIHEEM.SYS
-                                NEWMENU.COM
                          INSTALLATION INSTRUCTIONS
@@ Regel 29: / Regel 27: @@
 INTRODUCTION:
-   This program will allow a COMPAQ 386 system to run the NURSING STAFFING
+    MNMIHEEM.SYS is a program executed from CONFIG.SYS that allows an IBM
-   PROGRAM by medical Information Processing Systems, Inc.  (This is used
+    EGA adapter to function properly in any Compaq 486-based system.
-   by WAUSAU Hospital.)
 SYSTEM REQUIREMENTS:
-   Any COMPAQ 386 system.
+    Any Compaq system that:
-   COMPAQ DOS version 3.00 or later.
+.  Uses an Intel 486 processor.
+.  Has an IBM EGA adapter installed.
+.  Uses DOS version 3.0 or newer as its operating system.
 WHO SHOULD USE:
-   Use this program if you cannot display a graph with the NURSING
+    When an IBM EGA adapter is placed in a Compaq 486-based system, three
-   STAFFING PROGRAM and the system hangs.
+    beeps (one very long, two long) occur during initialization.  The
+    machine then boots in 40-column mode.  In an MS-DOS environment, the
+    adapter can be returned to 80-column mode by typing MODE CO80 from a
+    DOS prompt, however, all EGA functionality is NOT regained.
 HOW TO USE:
-.   Copy NEWMENU.COM from the distribution diskette to the directory
+    Copy the file MNMIHEEM.SYS to the disk or diskette you will be booting
-        that contains the MENU.EXE program.
+    from, using the DOS copy command:
-.   To run MENU.EXE, make the current directory the one which contain
+         copy a:\mnmiheem.sys d:\path\mnmiheem.sys
-        MENU.EXE and the patch file.  Type MENU.EXE and  press <ENTER>.
-        Any command line parameters that were used with MENU.EXE can be
-        added before pressing <ENTER>.
-.   You will see the following message when the program is run:
+    where d:\path\mnmiheem.sys shows the drive and directory in which the
+    program is to be stored and the device from which to boot.
-             NEWMENU.COM          Version 1.00
+    Using the file editor of your choice, place the following line as the
-             (C) Copyright COMPAQ Computer Corp. 1990
+    first line in the CONFIG.SYS file:
-.   If you usually start MENU.EXE in your AUTOEXEC.BAT, edit your
+         device=d:\path\mnmiheem.sys.
-        AUTOEXEC.BAT to run NEWMENU.COM instead.
+    When the system boots, the beeps described above still occur, but
+    shortly thereafter the screen goes blank for a short period and then
+    displays in 80-column mode.  No installation messages are given.
 EFFECTS ON YOUR SYSTEM:
-.   NEWMENU.COM version 1.00 will require around 900 bytes of memory.
+    After re-initializing the EGA adapter, this program leaves no residue
+    in your system.
 </file>