Verschillen

Dit geeft de verschillen weer tussen de geselecteerde revisie en de huidige revisie van de pagina.

--- overig:compaq:softpaq:sp0030 [08-01-2022] – aangemaakt michel
+++ overig:compaq:softpaq:sp0030 [08-01-2022] (huidige) – aangemaakt michel
@@ Regel 3: / Regel 3: @@
 ---- dataentry compaq_softpaq ----
 Extensie  : zip
-Grootte   : 19 kB
+Grootte   : 11 kB
-Titel     : This device driver is needed for versions of MS OS/2 BEFORE Version 1.2x, to support a mouse attached to the Pointing Device Interface Port on COMPAQ System Units.
+Titel     : This device driver enables an IBM Enhanced Graphics Adaptor (EGA) to be run in any COMPAQ 80486-based system.  Otherwise it comes up in 40 cloumn mode and nver gets full EGA functionality.
 Versie    :
 Taal      :
@@ Regel 15: / Regel 15: @@
 ^ Bestand      ^
-| MOUSEA05.SYS |
+| MNMIHEEM.DOC |
-| README       |
+| MNMIHEEM.SYS |
 ===== Tekst-bestanden =====
-<file txt README>
+<file txt MNMIHEEM.DOC>
-       MS OS/2 MOUSE DRIVER FOR COMPAQ DESKPRO 386s AUXILIARY INPUT PORT
+                                MNMIHEEM.SYS
+                         INSTALLATION INSTRUCTIONS
-           Copyright (C) 1988 by Microsoft Corporation
-           Copyright (C) 1988 by Compaq Computer Corporation
-           COMPAQ Registered U.S. Patent and Trademark Office
-           DESKPRO 386s is a trademark of Compaq Computer Corporation
- This disk contains the MS OS/2 device driver for a Microsoft Mouse connected
+INTRODUCTION:
- to the COMPAQ DESKPRO 386s auxiliary input port.  The driver works with
- MS OS/2 Standard Version 1.0 and the 1.1 SDK.  To install with MS OS/2
- Version 1.0, insert the diskette in drive A: and type the following command:
-         COPY A:MOUSEA05.SYS C:\OS2
+    MNMIHEEM.SYS is a program executed from CONFIG.SYS that allows an IBM
+    EGA adapter to function properly in any Compaq 486-based system.
- Modify CONFIG.SYS to include the following two lines:
-         DEVICE=C:\OS2\MOUSEA05.SYS
+SYSTEM REQUIREMENTS:
-         DEVICE=C:\OS2\POINTDD.SYS
- Remove the diskette and reboot by pressing CTRL + ALT + DELETE.
+    Any Compaq system that:
- For use with the MS OS/2 Version 1.1 SDK, use the C:\OS2\DEV directory.
+.  Uses an Intel 486 processor.
- Refer to the "Installing Device Drivers" chapter of the MS OS/2 Reference
+.  Has an IBM EGA adapter installed.
- Guide for more information.
+.  Uses DOS version 3.0 or newer as its operating system.
+WHO SHOULD USE:
+    When an IBM EGA adapter is placed in a Compaq 486-based system, three
+    beeps (one very long, two long) occur during initialization.  The
+    machine then boots in 40-column mode.  In an MS-DOS environment, the
+    adapter can be returned to 80-column mode by typing MODE CO80 from a
+    DOS prompt, however, all EGA functionality is NOT regained.
+HOW TO USE:
+    Copy the file MNMIHEEM.SYS to the disk or diskette you will be booting
+    from, using the DOS copy command:
+         copy a:\mnmiheem.sys d:\path\mnmiheem.sys
+    where d:\path\mnmiheem.sys shows the drive and directory in which the
+    program is to be stored and the device from which to boot.
+    Using the file editor of your choice, place the following line as the
+    first line in the CONFIG.SYS file:
+         device=d:\path\mnmiheem.sys.
+    When the system boots, the beeps described above still occur, but
+    shortly thereafter the screen goes blank for a short period and then
+    displays in 80-column mode.  No installation messages are given.
+EFFECTS ON YOUR SYSTEM:
+    After re-initializing the EGA adapter, this program leaves no residue
+    in your system.
 </file>